403 Stainless Steel (UNS S40300 / 1.4005) Supplier

Available Forms

As a 403 stainless steel manufacturer in China, Kongfang Metal provide a wide range of 403 materials.

Cold Rolled Stainless Steel Sheet

403 Sheet

Cold Rolled
Width: 1000 - 2000mm
Thickness: 0.3 - 6.0mm

Hot Rolled Stainless Steel Plate

403 Plate

Hot Rolled
Width: 1000 - 2000mm
Thickness: 3 - 100mm

Cold-Rolled Stainless Steel Coil

403 Cold-Rolled Coil

Cold Rolled
Width: 1000 - 2000mm
Thickness: 0.3 - 6.0mm

Hot-Rolled Stainless Steel Coil

403 Hot-Rolled Coil

Hot Rolled
Width: 1000 - 2000mm
Thickness: 3 - 14mm

Stainless Steel Strip

403 Strip

Width: 7 - 600mm
Thickness: 0.3 - 10mm

Stainless Steel Seamless Pipe

403 Seamless Pipe

OD: ≤610mm
WT: 1 - 100 mm

Stainless Steel Welded Pipe

403 Welded Pipe

OD: 6 - 3000mm
WT: 1 - 100 mm

Stainless Steel Round Bar

403 Round Bar

Diameter: 1 - 200mm
Length: 100 - 12000mm

Stainless Steel Flat Bar

403 Flat Bar

Width: 20 - 800 mm
Thickness: 3 - 60 mm

Stainless Steel Angle Bar

403 Angle Bar

Side Length: 20 - 250 mm
Thickness: 3 - 35 mm

Stainless Steel Channel

403 Channel

Height: 50 - 400 mm
Thickness: 4 - 20 mm

Stainless Steel H Beam

403 H Beam

Height: 100 - 1000 mm
Thickness: 6 - 40 mm

If you need a strong, heat-treatable stainless steel for turbine blades, fasteners, or engine parts, 403 stainless steel is your practical choice.

It combines excellent oxidation resistance, moderate corrosion resistance, and high mechanical strength after hardening—ideal where 304 is too soft and 410 too brittle.

Heat-resistant stainless steel turbine blades, fasteners, and engine parts made of 403 stainless steel on a brushed metal surface.

Standards and Equivalent Grades

ASTM UNS EN DIN GOST GB
403
S40300
1.4000
X6Cr12
12Х12
1Cr12

Chemical Composition

Grade Standard C Cr Ni Mn Si P S Fe
403
ASTM A240
0.08 – 0.15
11.5 – 13.0
≤ 0.5
≤ 1.0
≤1.0
≤ 0.04
≤0.03
Balance
1.4000
EN 10088-2
0.08 – 0.15
11.5 – 13.0
≤ 0.5
≤ 1.0
≤ 1.0
≤ 0.04
≤ 0.03
Balance
SUS403
JIS G 4304
JIS G 4305
0.08 – 0.15
11.5 – 13.0
≤ 0.5
≤ 1.0
≤1.0
≤ 0.04
≤0.03
Balance

Mechanical Properties of AISI 403

403 stainless steel achieves high strength and toughness after heat treatment while retaining good ductility and machinability in the annealed state.

Grade Standard Tensile Strength Yield Strength Elongation Hardness (Brinell)
403
ASTM A240
≥ 485 MPa
≥ 275 MPa
≥ 20 %
≤ 217 HBW
1.4000
EN 10088-2
≥ 500 MPa
≥ 275 MPa
≥ 20 %
≤ 217 HBW
SUS403
JIS G4304/4305
≥ 480 MPa
≥ 260 MPa
≥ 20 %
≤ 217 HBW

After quenching and tempering, hardness can reach up to 500 HBW depending on the tempering temperature.

Precision machined stainless steel turbine and engine components showcasing polishability, hardness, and metallic luster of 403 stainless steel.

Key Features

  • Heat-treatable martensitic structure → high hardness and strength

  • Reliable oxidation resistance up to 650 °C (1200 °F)

  • Excellent machinability compared to 410/420 grades

  • Magnetic in both annealed and hardened conditions

  • Good polishability for turbine or precision machined parts

Corrosion & Oxidation Resistance

403 performs well in air, steam, mild alkali, and organic acid environments.
However, it is not recommended for marine or chloride-rich conditions where 316L or duplex grades excel.
After polishing and passivation, surface film stability improves significantly, extending component life under thermal cycling.

Polished stainless steel industrial valve and pipe fittings demonstrating 403 stainless steel’s oxidation and corrosion resistance in steam environment.

Processing & Fabrication

Stainless Steel Machinability
Machinability

Machine in annealed state with rigid tools and controlled feeds. Preheat ~200 °C (400 °F) for forging.

Stainless Steel Weldability
Weldability

Possible with TIG/MIG methods; use pre-heat (~200 °C) and post-heat treatment to reduce cracking.
Recommended filler: E410 or matching composition.

Stainless Steel Heat Treatment
Heat Treatment

Anneal at 790–815 °C (1450–1500 °F), air cool. Harden at 950–980 °C (1740–1800 °F) then oil or air quench.
Temper between 150–370 °C (300–700 °F) for desired hardness.

Stainless Steel Surface Finishing
Surface Finishing

Pickling, grinding, and mirror polishing restore corrosion resistance and surface brilliance.

403 vs 410 vs 420 Stainless Steel

Property 403 410 420
Carbon (%)
0.08–0.15
0.08–0.15
0.15–0.40
Chromium (%)
11.5–13
11.5–13.5
12–14
Hardness (after treatment)
High
High
Very High
Corrosion Resistance
Good
Moderate
Moderate
Toughness
Better than 410
Standard
Lower
Machinability
Excellent
Fair
Poor
Typical Use
Turbine & Fasteners
Cutlery & Machinery
Blades & Tools
Stainless steel turbine blades, compressor shafts, and forged casings representing industrial and aerospace applications of 403 stainless steel.

Industrial Applications

  • Steam turbine blades and rotor discs

  • Compressor shafts and bolts

  • Heat-resistant casings and forgings

  • Pump valves, couplings, and bushings

  • Power generation components and aircraft hardware

Heat Resistance

403 stainless steel maintains oxidation resistance up to 650 °C (1200 °F) and can briefly withstand 700 °C without scale formation.
It’s frequently used for gas turbines, furnace parts, and exhaust systems where mechanical integrity matters more than full corrosion immunity.

Workability & Formability

While harder than austenitic grades, 403 offers good cold-forming in the annealed condition.
Pre-heating and controlled temperatures during forming reduce cracking risk and improve dimensional accuracy.

Purchasing Tips

  • Verify heat treatment state (annealed / tempered / hardened).

  • Request MTC (EN 10204 3.1) and surface finish info.

  • For machined components, specify tolerance and grain direction.

  • ISO-certified management systems within the Kongfang group; CE documentation for applicable products and orders; independent third-party inspection available on request.

FAQs

Is 403 magnetic?

Yes — it remains magnetic in all conditions due to its martensitic structure.

How does 403 compare to 410?

403 offers slightly better toughness and machinability, ideal for turbine hardware.

Can 403 be used in marine conditions?

Not recommended for immersion; use 316L or duplex grades instead.

What’s the maximum service temperature?

Around 650 °C continuous use; short spikes to 700 °C are acceptable.

Does 403 need post-weld heat treatment?

Yes — PWHT is essential to restore ductility and prevent cracking.

What forms does Kongfang Metal supply?

Plates, coils, bars, rods, forgings, and custom machined components with export documentation and test certificates.

Why Kongfang Metal?

If you need high-strength, heat-resistant 403 stainless steel for industrial applications, 📩 contact Kongfang Metal today.

✅ 10,000+ customers served across domestic and international markets
✅ Export transactions in 30+ countries across six continents
✅ ISO-certified management systems within the Kongfang group
✅ CE documentation for applicable products and orders
✅ Independent third-party inspection available on request
✅ 20,000 metric tons of saleable inventory
✅ Professional export packaging and fast delivery
✅ Free samples, mill test certificates, and cut-to-size services available

Kongfang Metal Factory
en_USEN
Send Your Inquiry Today

Scan to add on WeChat

Kongfang Metal WeChat-QR-Code