PREN Calculator
Formula & Notes
PREN is an empirical index used to compare resistance to chloride pitting. We use: PREN = %Cr + 3.3×(%Mo + 0.5×%W) + 16×%N. For grades without W, set %W = 0 and the formula reduces to the classic PREN = %Cr + 3.3×%Mo + 16×%N. Always confirm final material selection with mill test certificates and design standards.
© Kongfang Metal — Tools
Use PREN to compare stainless steel compositions when screening materials for chloride-pitting service. For a comparison such as 304 vs 316, start with the grade or heat chemistry, then consider the actual environment and fabrication condition when selecting material.
Illustrative chemistry: Cr 18%; Mo 0%; W 0%; N 0.05%.
PREN = 18 + 3.3 × 0 + 16 × 0.05 = 18.8.
For a quoted heat, replace these example inputs with its certificate chemistry.
What Is PREN and Why Should You Care?
PREN means Pitting Resistance Equivalent Number.
It is a simple formula that links chemical composition to resistance to chloride pitting.
You use it to:
Compare different grades (304 vs 316L vs 2205 vs 2507, etc.)
Compare a composition with the displayed bands and material references
Communicate with suppliers and engineers using one clear index
Use PREN as a composition-based comparison alongside the product specification, service conditions and relevant corrosion-test data.
PREN Formula Used in This Calculator
Your calculator uses the extended PREN formula with tungsten (W):
PREN = %Cr + 3.3 × (%Mo + 0.5 × %W) + 16 × %N
%Cr – Chromium content (wt%)
%Mo – Molybdenum content (wt%)
%W – Tungsten content (wt%)
%N – Nitrogen content (wt%)
If your grade has no tungsten, you simply set W = 0.
In that case, the formula becomes:
PREN = %Cr + 3.3 × %Mo + 16 × %N
This is the classic PREN formula that you see in many textbooks and datasheets.
So with one calculator, you cover:

How the PREN Calculator Works
The calculator is designed to be simple and fast, even if you are not a metallurgist.
Step 1 – Pick a Grade
At the top, you see a Grade / Alloy dropdown, for example:
AISI 304
AISI 316L
Duplex 2205
Super Duplex 2507
904L
254SMO
Nickel Alloy 625
Alloy C-276
Custom composition
When you choose one grade, the calculator:
Loads a typical Cr / Mo / W / N composition for that grade
Fills the four input boxes with those values
Instantly calculates a PREN value
Default is AISI 304, so you see a result right away.
This is only a typical composition. Actual heats will vary. For critical designs, you should always use real MTC numbers from mill certificates.
Step 2 – Adjust the Composition
You see four input boxes:
%Cr (wt%)
%Mo (wt%)
%W (wt%)
%N (wt%)
You can:
Keep the default values for a quick estimate
Or replace them with numbers from your actual MTC
For grades without tungsten, just leave %W = 0
The calculator updates the PREN in real time as soon as you change any value.
Step 3 – Read the PREN Value and Comparison Band
The result area shows:
PREN value – The number from the formula
Chemistry – A short line like
Cr 22.50 · Mo 3.00 · W 0.00 · N 0.170Comparison band – A simple text band, such as:
Lower PREN band — 304 reference (austenitic family)
Intermediate band — 316L / lean duplex reference
Higher band — 2205 / 904L reference (Duplex comparison)
6Mo / super duplex comparison region
High calculated PREN — use alloy-specific corrosion data
You also see a sticky bar at the bottom of the card:
Shows PREN value and comparison band even when you scroll
Makes it easy to screenshot or reference while reading your page
Step 4 – Copy Results and Share
There is a Copy button.
When you click it, the tool:
Collects the grade name
Formula in use
Composition values you entered
PREN value and comparison band
Adds a short note that PREN is only a comparative index
You can paste this result into:
Emails to your customer
Internal notes to your engineering team
Chat messages (WhatsApp, WeChat, Telegram, etc.)
The Reset button brings everything back to AISI 304 with typical values.
How to Read PREN Values – Simple Bands
Use these five display bands to compare compositions and find a material reference. They are comparison bands, not service-approval limits.
| Calculated PREN | Comparison band |
|---|---|
| PREN < 24 | Lower PREN band — 304 reference |
| 24 ≤ PREN < 32 | Intermediate band — 316L / lean duplex reference |
| 32 ≤ PREN < 40 | Higher band — 2205 / 904L reference |
| 40 ≤ PREN < 50 | 6Mo / super duplex comparison region |
| PREN ≥ 50 | High calculated PREN — use alloy-specific corrosion data |
Material references
| Material | Composition-based PREN reference |
|---|---|
| 304 | 17.5–20.8 |
| 316 / 316L | 23.1–28.5 |
| 2205 | 30.8–38.1 |
| 904L | 32.2–39.9 |
| 1.4547 (6Mo) | 42.2–47.6 |
| 2507 | >40 |
These reference ranges overlap the display bands. They help compare materials; they do not identify a grade or approve a service environment. Source: BSSA PREN comparison table.
Compare two or three candidate compositions using the same formula, then use the water-system shortlist and service data below to assess the application.
35.1 falls in 32 ≤ PREN < 40: Higher band — 2205 / 904L reference. The band is a material comparison; use the actual chemistry to identify the grade.
Examples – What Does the PREN Calculator Tell You?
Here are some typical approximate values you might see when you use the calculator with preset compositions:
(Numbers are approximate and only for illustration.)
304
Cr ≈ 18%, Mo ≈ 0%, W = 0, N ≈ 0.05
PREN ≈ 18 + 3.3×0 + 16×0.05 = 18 + 0 + 0.8 = 18.8
→ Lower PREN band — 304 reference316L
Cr ≈ 17%, Mo ≈ 2.1%, W = 0, N ≈ 0.05
PREN ≈ 17 + 3.3×2.1 + 16×0.05 ≈ 17 + 6.93 + 0.8 ≈ 24.7
→ Intermediate band — 316L / lean duplex referenceDuplex 2205
Cr ≈ 22.5%, Mo ≈ 3.0%, W = 0, N ≈ 0.17
PREN ≈ 22.5 + 3.3×3.0 + 16×0.17 ≈ 22.5 + 9.9 + 2.72 ≈ 35.1
→ Higher band — 2205 / 904L referenceSuper Duplex 2507
Cr ≈ 25%, Mo ≈ 4%, W = 0, N ≈ 0.27
PREN ≈ 25 + 3.3×4 + 16×0.27 ≈ 25 + 13.2 + 4.32 ≈ 42.5
→ 6Mo / super duplex comparison regionUNS S31254 (254SMO) — illustrative composition
Cr 20.0%; Mo 6.1%; W 0%; N 0.20%
PREN = 20 + 3.3 × 6.1 + 16 × 0.20 = 43.33
Displayed PREN: 43.3
For a specific heat, enter the composition reported on its material certificate.→ 6Mo / super duplex comparison region
Alloy 625 (Ni alloy, with high Mo)
Cr ≈ 21.5%, Mo ≈ 9.0%, W = 0, N ≈ 0.02
PREN ≈ 21.5 + 3.3×9 + 16×0.02 ≈ 21.5 + 29.7 + 0.32 ≈ 51.5
→ High calculated PREN — use alloy-specific corrosion data
With the calculator, you can:
Plug in your exact MTC data instead of typical values
See how small changes in Mo or N move your material between bands
Compare the stated chemistry and calculated PREN alongside price, product condition and matching corrosion data
PREN of the illustrative compositions above
All six values use the same stated formula and the example chemistry above. Use actual heat chemistry for a purchasing comparison.
When Should You Use PREN in Your Daily Work?
You use this PREN calculator whenever you need to make or check a material choice for chloride conditions:
Typical cases
Seawater or brackish water piping
Desalination plants
Chemical tank farms with chlorides
Offshore structures and equipment
Heat exchangers with seawater cooling
Pulp and paper bleach plants
Food processing with chlorides (sauces, brines, etc.)
- Read chloride concentration from the water report.
- Record temperature, immersion or splash exposure, and crevice conditions.
- Use the water-system shortlist below, then compare matching corrosion data and the specified PREN requirement.
Practical use examples
- For 316L and 2205 offers, enter each quoted heat’s chemistry and compare PREN using the same formula. Compare price and product specification alongside that result.
- If the customer asks for “super stainless”, start with the water report and operating conditions. Use the shortlist below to compare 6Mo or super duplex candidates where the chloride range calls for them.
- For a low-Mo heat of 316L, check the MTC chemistry against the specified composition and any project PREN limit. Record the calculated result before accepting the heat against those requirements.
PREN helps you speak in numbers, not feelings.
Using PREN with Service and Fabrication Conditions
Read the comparison alongside the operating temperature, chloride exposure, surface condition and fabrication route. IMOA — composition and pitting resistance.
PREN does not fully capture:
Crevice corrosion behavior
Effects of welds, heat tint, or poor pickling
Microstructure issues (sigma phase, chi phase, etc.)
Surface finish, roughness, and contamination
Temperature, pH, and complex chemical mixtures
So you should use PREN together with:
Relevant standards (ASTM, EN, NORSOK, etc.)
Lab test data (ASTM G48, critical pitting temperature, etc.)
Design codes and customer specifications
Good fabrication and cleaning practice
The calculator also assumes that:
The composition you enter is accurate (for example from MTC)
The material is properly produced, heat treated, and welded
The surface is correctly cleaned and passivated
If these conditions are not met, even a high-PREN material may still fail.
How You Can Use This Calculator in Your Workflow
Here are some practical ideas for you:
1. During Sales and Quotation
Compare candidate grades live when you talk with a client
Paste PREN results into your quotation to show added value
Explain why a cheapest option might be unsafe in the long term
2. During Design and Material Selection
First shortlist by water conditions, then compare PREN
Water-system shortlist — chloride concentration (mg/L)
Below 200: compare 304/304L first.
200 to below 1,000: compare 316/316L first.
1,000–3,600: include 2205 in the comparison.
Above 3,600 up to 26,000 (brackish/seawater): compare 6Mo austenitic and super duplex grades.
Use this as an initial shortlist for ambient supply-water and water-treatment conditions covered by BSSA SSAS4.92 (Issue 02, 2001). Start with the water report’s chloride result. Above 26,000 mg/L, use brine-specific corrosion data. For hot, stagnant, heavily chlorinated or deposit-prone service, obtain corrosion data matching those conditions before choosing from the shortlist. Minimise crevices, remove weld heat tint and avoid stagnant sections.
After shortlisting the grades, compare their PREN using the same formula and the stated chemistry. For immersion or splash-zone service, also compare data matching the actual temperature and crevice conditions. Follow a project’s specified PREN limit where one is stated; 32, 40 and 50 are not universal seawater acceptance limits.
Source: BSSA SSAS4.92, Issue 02 (2001), Stainless Steels in Supply and Waste Waters. Chloride concentration is not the residual-chlorine dose.
3. During Quality Checks
Take actual Cr / Mo / W / N from the MTC
Enter them into the calculator
Confirm that delivered material meets your minimum PREN target
This makes your quality check process visual and fast.
FAQ
Q1. Do you need to be a metallurgist to use this calculator?
No. You only need four numbers: %Cr, %Mo, %W, and %N.
You can get them from a mill test certificate (MTC) or a reliable datasheet.
Q2. What if my grade has no tungsten (W)?
Simply set %W = 0.
The formula then becomes the classic:
PREN = %Cr + 3.3×%Mo + 16×%N
The calculator handles this automatically.
Q3. Why does the calculator include W (tungsten)?
Because some high-performance stainless steels and nickel alloys use W to improve pitting resistance.
Tests show that W behaves somewhat like Mo, but its effect is weaker.
That is why the formula uses 0.5 × %W inside the Mo term.
Q4. Are the preset compositions exact?
No. They are typical values from common datasheets.
Real heats can be slightly higher or lower.
For critical decisions, you should always use the exact numbers from your MTC.
Q5. Is a higher PREN always better?
For composition-based comparison, a higher PREN indicates a higher pitting-resistance index. To choose a grade, compare corrosion data for the actual water, temperature and crevice conditions.
However, higher PREN also means:
More alloy elements → higher cost
Sometimes more difficult welding or fabrication
Possible need for more strict handling
Start with the water-system shortlist above, then compare the shortlisted grades against the project’s service and fabrication requirements.
Q6. Can PREN predict crevice corrosion or stress corrosion cracking?
Not directly.
PREN is designed for pitting resistance, not for all types of corrosion.
You should combine PREN with:
Experience in similar service
Lab test data and standards
Good design and fabrication practice
Q7. My client only wrote “use 316L”. Can I use PREN to propose a better grade?
Yes. You can:
Enter a typical 316L composition and show the PREN.
Enter a duplex or super duplex grade and show its higher PREN.
Use the water-system shortlist and matching corrosion data to explain which candidate fits the chloride level, temperature and crevice conditions.
PREN gives you a clear number to support your proposal.
Q8. Can I use this calculator for nickel alloys like 625 or C-276?
Yes. The tool already includes Nickel Alloy 625 and Alloy C-276 as presets.
You can also create your own custom composition for other nickel alloys.
Just remember that:
Nickel alloys may have many other elements
PREN focuses only on Cr, Mo, W, and N
Other alloying elements also affect corrosion in reality
Q9. What if I only know Cr and Mo, but not N or W?
You can still use the calculator:
Set N and W to 0, if they are very low
Or use typical values from a reliable datasheet as an estimate
The result will not be perfect, but it is still better than no number at all.
Q10. Can I use PREN to set internal material rules?
Yes, where the project specification defines a PREN limit for stated service conditions.
You can, for example, define:
Cooling water projects: PREN ≥ X
Full seawater exposure: PREN ≥ Y
You then check each material choice with the calculator.
Just make sure these rules match:
Your company’s experience
Applicable standards
Your risk level for failure
Q11. Does the calculator replace corrosion testing?
No. It is a quick selection and comparison tool, not a test.
Real corrosion behavior depends on many factors that a simple formula cannot fully capture.
Use the calculator to narrow down options and to communicate clearly, then validate final choices with:
Test data
Standards
Specialist advice
Q12. How should you present PREN to your customers?
You can:
Show the PREN value alongside the grade name in quotations
Explain which band it falls into (for example “Higher band — 2205 / 904L reference”)
Add a short note: “PREN is a comparative index for chloride pitting resistance.”
State the grade, chemistry source and calculated index so customers can compare the material on a clear basis.
Related Tools
Explore other engineering calculators by Kongfang Metal:
Metal Weight Calculator — Quickly calculate the weight of plates, pipes, and bars by size and density.
Coil Calculator — Find coil weight, length, or outer diameter instantly.
Metal Density Chart — Reference densities of common metals and alloys.
Stainless Steel Grade Comparison Tool — Compare mechanical and chemical properties across grades.


